The Spares Company
Club Shop/Regalia
Parent Website
Contact Officials
Machine Registrar
Club Secretary
Membership Secretaries
MPH Editor and Forum Administrator.
Section Newsletters
Technical Databases
Photos
Home
What's new
Latest activity
Forums
New posts
What's new
New posts
Latest activity
Information
Bike Modifications
Machine Data Services
Manufacturers Manuals
Spare Parts Listings
Technical Diagrams
Whitakerpedia (Vincent Wiki)
The Club
MPH Material Archive
Flogger's Corner
Obituaries
VOC Sections
Local Sections
Local Section Newsletters
Miscellaneous
Club Assets
Club History
Club Rules
Machine Data Services
Meeting Documents
Miscellaneous
Essential Reading
Magazine/Newspaper Articles/Letters
Adverts and Sales Brochures
The Mighty Garage Videos
Bikes For Sale (Spares Company)
Log in
Register
What's new
New posts
Menu
Log in
Register
Install the app
Install
Home
Forums
Forums: Public Access
Tech. Advice: Series 'B' / 'C' 500cc/1000cc Bikes
Cylinder Oil Feed on Comet
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Matty" data-source="post: 58907" data-attributes="member: 1339"><p>I am about to have my Series C Comet rebored from standard out to +20 thou. The standard resleeved barrel was fitted about 8 years ago with a VOC low expansion piston and after 35,000 miles the bike was using about a pint of oil in 150 miles and oiling up plugs, so I thought I had better fix it.</p><p> </p><p>I can get a 10 thou feller gage between the piston and liner half way up the bore so things are pretty worn !!</p><p> </p><p>The barrell has an oil hole which is drilled at an angle to be below the scraper ring, but the groove in the outside of the cylinder which connects to the hole in the crankcase mouth and in fact also the hole in the cylinder, are below the lower edge of the crankcase mouth - so the oil will run down the groove, past and over the hole to the cylinder and then into the crankcase !!</p><p> </p><p>I had previously attached a piece of very thin and carefully shaped shim to the cylinder, this came below the crankcase mouth so that the oil did not run straight into the crankcase, but I have been advised by various experts to simply blank off the oil feed in the timing cover to the cylinder, because with modern oils the feed was not necessary. I hoped this would reduce the oil consumption, but for the couple of years I tried this and it made no difference.</p><p> </p><p>So when I put the engine back together next week - is it OK to allow oil into the cylinder oiling system again and just let it run into the crankcase, should I put the shim in to ensure the oil does not go directly to the crankcase, or should I put a plastic washer behind the oil feed in the timing cover to stop any oil going to the cylinder oiler at all?</p><p> </p><p>Any advice would be welcome please, but I understand that the feeds in the crankcase mouths of twins are not positioned in the same place as that of the Comet and that the above problem does not arise with them and should my cylinder in fact be the same or different to those used on twins?</p><p> </p><p>Matty</p></blockquote><p></p>
[QUOTE="Matty, post: 58907, member: 1339"] I am about to have my Series C Comet rebored from standard out to +20 thou. The standard resleeved barrel was fitted about 8 years ago with a VOC low expansion piston and after 35,000 miles the bike was using about a pint of oil in 150 miles and oiling up plugs, so I thought I had better fix it. I can get a 10 thou feller gage between the piston and liner half way up the bore so things are pretty worn !! The barrell has an oil hole which is drilled at an angle to be below the scraper ring, but the groove in the outside of the cylinder which connects to the hole in the crankcase mouth and in fact also the hole in the cylinder, are below the lower edge of the crankcase mouth - so the oil will run down the groove, past and over the hole to the cylinder and then into the crankcase !! I had previously attached a piece of very thin and carefully shaped shim to the cylinder, this came below the crankcase mouth so that the oil did not run straight into the crankcase, but I have been advised by various experts to simply blank off the oil feed in the timing cover to the cylinder, because with modern oils the feed was not necessary. I hoped this would reduce the oil consumption, but for the couple of years I tried this and it made no difference. So when I put the engine back together next week - is it OK to allow oil into the cylinder oiling system again and just let it run into the crankcase, should I put the shim in to ensure the oil does not go directly to the crankcase, or should I put a plastic washer behind the oil feed in the timing cover to stop any oil going to the cylinder oiler at all? Any advice would be welcome please, but I understand that the feeds in the crankcase mouths of twins are not positioned in the same place as that of the Comet and that the above problem does not arise with them and should my cylinder in fact be the same or different to those used on twins? Matty [/QUOTE]
Insert quotes…
Verification
What was Mr Vincent's Christian Name?
Post reply
Home
Forums
Forums: Public Access
Tech. Advice: Series 'B' / 'C' 500cc/1000cc Bikes
Cylinder Oil Feed on Comet
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top